OkBike Logo
OkBike Logo
Home Verified Garages Serviceable Pincodes Hotspots Demand Partner (Mechanic Portal)
Book Doorstep Service Get on Google Play

Choose Your City

Explore verified bike garages & doorstep service across India

Language:

Fault Code P063F Diagnostic Solution

Step-by-step diagnostic checks, multimeter testing values, wiring inspections & OBD-II erase guides for BS6 two-wheelers.

OkBike App Icon

OkBike Mechanic App

Live sensor graphs, 1,000+ color wiring diagrams, ECU pinouts & OBD-II scanner.

P063F
ECU Computer & Output Circuits
Standard OBD-II Diagnostic Protocol
Share with Mechanic
Fault Description & Technical Meaning:

Auto Configuration Engine Coolant Temperature Input Not Present. This diagnostic trouble code has detected an abnormal operating condition or electrical signal failure. The Engine Coolant Temperature (ECT) Sensor measures engine cooling fluid temperature to regulate cold-start fuel enrichment, ignition timing advance, and radiator cooling fan switching. When this circuit fails, the vehicle computer illuminates the Check Engine / Warning Light and may log an active diagnostic fault code.

Diagnostic Summary: Diagnostic code P063F triggers due to a circuit malfunction affecting the Engine Coolant Temperature (ECT) Sensor, impacting proper vehicle operation.

Related Components (Photo & Inspection)

3 Components (Tap to Zoom)
EOT Sensor (Engine Oil Temperature)
Sensor

EOT Sensor (Engine Oil Temperature)

Click to inspect photo & test specs

IAT Sensor (Intake Air Temperature)
Sensor

IAT Sensor (Intake Air Temperature)

Click to inspect photo & test specs

12V Motorcycle Battery
Electrical

12V Motorcycle Battery

Click to inspect photo & test specs

Common Symptoms
  • • Check Engine Light (MIL Lamp): Illuminates or flashes on the speedometer console.
  • • Engine Hesitation & Jerking: Poor throttle response during sudden acceleration.
  • • Drop in Fuel Economy: Open-loop fuel spraying increases petrol consumption and causes black smoke.
  • • Hard Cold Starting: Engine dies during idle or requires multiple starter button attempts.
Common Root Causes
  • • Wiring Harness Damage: Chafed wires touching motorcycle frame metal or rodent cuts.
  • • Loose / Corroded Coupler: Green oxidation or loose push-fit pins inside connector plug.
  • • Defective Component: Burnt internal sensing thermistor or solenoid actuator coil.
  • • Low Battery Voltage: Weak motorcycle battery under 12.0V causing ECU reference error.

Step-by-Step Diagnostic & Repair Procedure

Bench-tested repair procedure for code P063F

5 Steps
Step 1: Turn off the vehicle ignition switch, remove the key, and allow all electrical and mechanical systems to cool down completely. Locate the Engine Coolant Temperature (ECT) Sensor, typically positioned screwed into the cylinder head cooling passage or thermostat housing.
Step 2: Carefully unplug the electrical wiring coupler from the Engine Coolant Temperature (ECT) Sensor. Inspect the connector pins and socket terminals for green copper corrosion, water moisture, bent pins, or melted plastic. Trace the wiring harness back toward the control module and check for chafing, wire cuts, or melted insulation touching vehicle metal.
Step 3: Set a digital multimeter to DC Volts and turn the ignition key ON without starting the engine. Check for proper electrical reference voltage (5.0V reference or 12V battery power depending on component specification). Next, set the meter to Ohms (continuity) and measure the signal wire voltage and ground continuity with a digital multimeter to ensure the ground circuit has less than 0.5 Ohms resistance to the chassis ground.
Step 4: Bench-test the component by measuring its internal resistance across the electrical terminals using your multimeter (NTC thermistor resistance (approx 2,000-3,000 Ohms cold at 20°C, decreasing smoothly to 200-350 Ohms at full engine operating temperature 90°C)). If the component is carbon-fouled, contaminated, or has poor pin tension, clean it carefully using dedicated electrical contact cleaner. If the internal coil or sensor circuit shows zero Ohms (short) or infinite Ohms (open), replace the component with a genuine OEM part.
Step 5: Reconnect the electrical coupler firmly until the locking tab audibly clicks into place. Connect an OBD-II diagnostic scanner or use the OkBike Mechanic App to erase stored DTC fault memory from the ECU. Start the engine or power up the vehicle, perform a test drive covering varied speeds, and verify that the Warning Light remains permanently turned off.
Important Note: Simply replacing the sensor does not immediately clear the Check Engine Light (MIL). Connect an OBD-II scanner to the motorcycle diagnostic connector and execute "Erase Stored DTC Memory" followed by a road test.

Related Diagnostic Fault Codes

P063C Generator Voltage Sense Circuit A Low. This diagnostic trouble code indicates that signal voltage has dropped below the minimum calibrated threshold (typically indicating a short-circuit to chassis ground or a dead sensor). The 12V Battery & Charging System supplies clean electrical power to the vehicle ECU, fuel pump, ignition coils, and electronic sensors. When this circuit fails, the vehicle computer illuminates the Check Engine / Warning Light and may log an active diagnostic fault code.
P063D Generator Voltage Sense Circuit A High. This diagnostic trouble code indicates that circuit voltage exceeds the maximum allowable threshold (typically indicating a short-circuit to 12V battery power or a missing ground). The 12V Battery & Charging System supplies clean electrical power to the vehicle ECU, fuel pump, ignition coils, and electronic sensors. When this circuit fails, the vehicle computer illuminates the Check Engine / Warning Light and may log an active diagnostic fault code.
P063E Auto Configuration Throttle Input Not Present Bank 1. This diagnostic trouble code has detected an abnormal operating condition or electrical signal failure. The Throttle Position Sensor (TPS) detects throttle butterfly valve opening angle when the rider or driver twists the throttle grip or presses the accelerator. When this circuit fails, the vehicle computer illuminates the Check Engine / Warning Light and may log an active diagnostic fault code.
P0640 Intake Air Heater Control Circuit. This diagnostic trouble code has detected an abnormal operating condition or electrical signal failure. The Powertrain Diagnostic Subsystem controls essential electronic fuel, air, and ignition parameters to maintain stable combustion and low exhaust emissions. When this circuit fails, the vehicle computer illuminates the Check Engine / Warning Light and may log an active diagnostic fault code.
P0641 Sensor Reference Voltage A Circuit/Open. This diagnostic trouble code indicates a broken wire, disconnected coupler, or internal open circuit causing complete loss of electrical connection. The Powertrain Diagnostic Subsystem controls essential electronic fuel, air, and ignition parameters to maintain stable combustion and low exhaust emissions. When this circuit fails, the vehicle computer illuminates the Check Engine / Warning Light and may log an active diagnostic fault code.
P0642 Sensor Reference Voltage A Circuit Low. This diagnostic trouble code indicates that signal voltage has dropped below the minimum calibrated threshold (typically indicating a short-circuit to chassis ground or a dead sensor). The Powertrain Diagnostic Subsystem controls essential electronic fuel, air, and ignition parameters to maintain stable combustion and low exhaust emissions. When this circuit fails, the vehicle computer illuminates the Check Engine / Warning Light and may log an active diagnostic fault code.